SILENT KNIGHT INSTALLATION, PROGRAMMING, AND OPERATION MANUAL Pdf Download | ManualsLib - Troubleshooting

Looking for:

5207 silent knight manual -  

Click here to DOWNLOAD

   

 

- Silent Knight SK Programming

 

Hide thumbs Also See for : Installation, programming, and operation manual 98 pages. Quick Links Download this manual. Security products should be tested every week to ensure complete and proper input and. To comply with industry standards, this product is equipped with line seizure.

Normally this 5207 silent knight manual will last approximately one minute, but, under adverse telephone. Previous Page. Next Kngiht. Page 2: System Overview It is important that msnual system be serviced as The 5207 silent knight manual for fire in up to 16 soon as possible to correct a trouble 5207 silent knight manual, or areas, within your facility.

Call your installation company When the encounters a fire, it for service immediately. Page 3 1. Press the key. Enter manuql valid operating code. Clack softener manual is active 24 hours a day and requires very little maintenance. Periodic Resetting an Alarm or Trouble testing will ensure that your knihgt is Warning operational at all times. The first Print page 1 Print document 4 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals?

Sign In Продолжить. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk. Upload from URL.

 

5207 silent knight manual. SILENT KNIGHT 5207 Installation, Programming, And Operation Manual

 

Hide thumbs Also See for : Installation, programming, and operation manual 98 pages. Quick Links Download this manual. Security products should be tested every week to ensure complete and proper input and. To comply with industry standards, this product is equipped with line seizure. Normally this condition will last approximately one minute, but, under adverse telephone. Previous Page.

Next Page. Page 2: System Overview It is important that your system be serviced as The monitors for fire in up to 16 soon as possible to correct a trouble zones, or areas, within your facility. Call your installation company When the encounters a fire, it for service immediately.

Page 3 1. Press the key. Enter a valid operating code. The is active 24 hours a day and requires very little maintenance. Avoid pulling one multiconductor cable for the entire panel. Figure Model Wiring Reference Refer to Table for available battery sizes and the maximum standby current load each can support. Figure is an example of a completed worksheet. Measure the alarm current. If only one current rating is listed, the draw for that device is the same whether the system is in alarm or standby condition.

Ensure that the total current of all items attached to the , including the itself, does not exceed 5 A when the panel is in alarm see Section 3. Page Power Supply Wiring Model power supply. Do NOT apply power to this panel until all accessories are properly connected. In all cases, the authority having jurisdiction takes pre- cedence. The cabinet outside dimensions are: Table on the next page lists the function and electrical rating of each terminal. See Section 3.

Notification device output 2 Positive Notification device output 1 Negative 1 amp max. Page Telephone Line Connection A situation could occur where both phone lines appear to be good, but the dialer cannot get through to the central station on the first line. In this case, the will switch phone lines and attempt the call again using the second line. Make sure the phone lines are programmed properly see Section 7. Model P2 Connects the zone expander to the Quick Connect P3 For temporarily connecting a for programming or troubleshooting.

Requires cable assembly not included. Page Compatible Product Installation Each class A zone is a four-wire circuit that allows an alarm to be detected even after a single open or ground fault occurs.

When a single open or ground fault occurs, the audible trouble signal will sound and the will report the trouble to the central station if programmed to report troubles.

Page Class B Style A Zones The detection of an open will cause the audible trouble signal to sound and the will report the trouble to the central station if programmed to do so. Figure shows how to wire a class B style A loop. One side of each class B loop connects to a zone input terminal and the other side of each loop connects to loop power. Model Status Display Module The Model Status Display module provides remote annunciation of alarm and trouble status information for each zone.

Make sure power is OFF at the panel before plugging in the Maintain a physical separation of one-half inch or more between field wires and connection points to prevent damage from transients. To install, fit the bracket over the power supply unit in the cabinet. With panel power OFF, use the cable provided to connect the to its connector P2 on the Insert screws provided. Place the four plastic stand- offs into the bracket and snap onto the PC board.

Page Model Direct Connect Module The maximum coil and wire resistance combined must not exceed 30 ohms. To install the for city box connection: 1. Locate the knockout on the right side of the cabinet to connect the using a short piece of conduit must not exceed 20 feet in length.

Page Nfpa 72 Polarity Reversal To install the for polarity reversal, follow the steps below: 1. Refer to the installation sheet shipped with the 95M for complete information. Note: The is not available from Silent Knight. It also provides trouble and alarm information and can be used for programming.

When the annunciator powers up, it will dis- play its ID code and current status of the panel. A temporary can be connected for programming and troubleshooting. See Section 4. Page Model Signal Power Expander The Model is a notification and auxiliary power expander that provides up to 6. Figure shows you how to connect the Model to the Model panel. Page Model Zone Converter 4. Figure and Figure show how to make conversions.

Page Supervised Notification Appliance Outputs Figure shows how to connect the notification circuits to the Contact Silent Knight if you have any questions about compatible notification circuits.

Page Auxiliary Relays loss of AC, low battery, failed to communicate, phone line troubles, and notification circuit troubles. Refer to the programming manual for more information. Figure shows the relay contact connections using a doorstrike application as an example.

Page Operation Section 5 Operation To operate the you can use either the built-in touchpad or the Model Remote Annunciator. Note that if no keys are pressed for 15 minutes while in program mode, the system will time out and resume normal operation. For complete information and for display messages, see Section 9. Table Built-in Touchpad Display Codes Page Led Indicators Operation 5. The chart below explains the meaning of these LEDs. In walk test mode, the built-in self test on the ESL series smoke detectors may be unreliable.

If the built-in self test is required, it should be done in the normal operating mode with the zone speed set to 3 seconds or higher. Please read Section 7 thoroughly, especially if you have never programmed the before.

The quick reference chart can be used for keeping track of how options have been pro- grammed for an installation. You must be in Step Programming Mode also known as mode 27 to program the panel.

See the following sections for details. Using Step Programming The digits appear on the right side of the display and scroll to the left as you continue to enter data. The way you move through Mode 27 may also vary from how it is described here.

Enable the printer if your installation includes a printer in- terface. The is not UL listed for use with the Enables 24V power. Do NOT disable. These digits are reserved by the manufacturer for future use. Page Step 3. More System Options Display Description Step 3 allows you to select seven system options shown below. To select an option, press its number. If you select this option, bells will pulse in the pattern shown below for customizing patterns, refer to Steps 27 and 28 : 3.

Page Step 5. Miscellaneous Options Display Description Step 5 is for programming several system options, including bell supervision. Select this option if you want walk tests reported to the central station.

Page 60 Note: This very fast response time can increase the possibility of false alarms, since transients and other interference can set off alarm conditions in such a short time span.

Silent Knight recommends that you do not use this response time unless you have to because, for example, the installation you are protecting requires this quick a response time even if false alarms could result.

Zones sec. Zone 8: sec. Page Step 7. Must be selected for all zones. Do NOT change the factory programming for this step. Page Step 8. If you want the to try again to send a report 15 minutes after all previous attempts have failed, select 0. Choose if using a second phone line with the system. Page Step Select a number from 5 to For a local- only system, select "0" for this step and for Step

   

 

5207 silent knight manual

   

Hide thumbs Also See for : Operator's manual 4 pages. Table Of Contents. Quick Links. Table of Contents. Previous Page. Next Page. Troubleshooting Troubleshooting 84 Troubleshooting and System Messages Page 2: Table Of Contents 3. Page 4 Section 8 Reporting Page 6: Introduction Section 1 Introduction The Model 5207 silent knight manual an 8-zone fire alarm control panel expandable up to 16 zones with a dig- ital communicator that meets NFPA 72 requirements.

The cabinet can be surface mounted or semi-flush mounted. Page 7: Optional Accessories For remote annunciation of alarm and trouble Module status information for 5207 silent knight manual zone. Page 8: Agency Listings And Requirements 4. If the causes harm mahual the telephone network, the telephone company will notify the user читать далее advance that temporary discontinuance of service may be required.

When advance notice is not practical, the telephone company will notify the user as soon as possible. Users have the right to file complaints, if necessary, with the Sillent Communications Commission. If the and its accessories are to be used as part of a UL installation, carefully read the UL requirements in this section.

The following applicable NFPA 72 standards can be Follow the current load restrictions shown in Section 3. Induced noise can interfere with telephone communication or even cause false alarms. Avoid pulling one /20846.txt cable for the entire panel. Figure Model Wiring Reference Refer to Table for available battery sizes and the maximum standby current load each can support.

Figure is an example of a completed worksheet. Measure the alarm current. If only one current rating is listed, the draw for 5207 silent knight manual device is the same whether the system is in alarm or standby condition. Ensure that the total current of all items attached to theincluding the itself, does not exceed 5 A when the panel is in alarm see Section 3. Page Power Supply Wiring Model power supply. Do 5207 silent knight manual apply power to this panel until all accessories are properly connected.

In all cases, the authority having jurisdiction takes pre- cedence. The cabinet outside dimensions are: Table on the next page lists the function and electrical rating of each terminal. See Section 3. Notification device manuwl 2 Positive Notification device output 1 Negative 1 amp max.

Page Telephone Line Connection A situation could occur where both phone lines appear to be good, but the dialer cannot get 5207 silent knight manual to the central station on the first line. In this case, the will switch phone lines and attempt the call again using the second line. Make sure the phone lines are 5207 silent knight manual properly see Section 5207 silent knight manual. Model P2 Mqnual the zone expander to the Quick Connect P3 For temporarily connecting a for programming or troubleshooting.

Requires cable sjlent not mahual. Page Compatible Product Installation Each class A zone is a four-wire circuit that allows an alarm to be detected even after a single open or ground fault occurs. When a single open or ground fault occurs, the audible trouble signal will sound and the will report the trouble to the central station if programmed to report troubles.

Page Class B Style A Zones The detection of an open will cause the audible trouble signal to sound and the will 5207 silent knight manual the trouble to the central station if programmed to do so. Figure shows how to wire a 5207 silent knight manual B style A loop. One side of each class B loop connects to a zone input terminal and the other side of each loop connects to loop power. Model Status Display Module The Model Status Display module provides remote annunciation of alarm and trouble status information for each zone.

Make sure power is OFF at the panel before plugging in the Maintain a physical separation of one-half inch or more between field wires and connection points to prevent damage from transients. To install, fit the bracket over the power supply unit in the cabinet. With panel power OFF, use the cable provided to connect the to its connector P2 on the Insert screws provided. Place the four plastic stand- offs into the bracket and snap onto the PC board.

Page Model Direct Connect Module The maximum coil and wire resistance combined must not exceed 30 ohms. To install the for city box connection: 1. Locate the knockout on the right side of the cabinet to connect the using a short piece of nanual must not exceed 20 feet in length.

Page Nfpa 5207 silent knight manual Polarity Reversal To install the for polarity reversal, follow the steps below: 1. Жмите to the installation sheet shipped with the 95M for complete information. Note: The is not available from Silent Knight. It also provides trouble and alarm information and can be 5207 silent knight manual for programming. When the annunciator powers up, it will dis- play its ID code and current status of the panel.

A temporary can be connected for programming and troubleshooting. See Section 4. Kjight Model Signal Sioent Expander The Model is a notification and auxiliary power expander that provides up to 6. Figure shows you how to connect the Model to the Model panel. Page Model Zone Converter 4.

Figure and Figure show how to make conversions. Page Supervised Notification Appliance Outputs Figure shows how to connect the notification circuits to the mnaual Contact Silent Knight if you have any questions about compatible notification circuits.

Page Auxiliary Relays mabual of AC, low battery, failed to communicate, phone line troubles, and notification circuit troubles. Refer to the programming manual for more information.

Figure shows the relay contact connections using a doorstrike application as an example. Page 5207 silent knight manual Section читать полностью Operation To operate the you can use either the built-in touchpad maanual the Model 5207 silent knight manual Annunciator. Note that if no keys are pressed for 15 minutes while in program mode, the system will time out and resume normal operation.

For 5207 silent knight manual information and for display messages, see Section 9. Table Built-in Touchpad Display Codes 5207 silent knight manual Led Indicators Operation 5. The chart below explains the meaning of these LEDs. In walk test mode, the built-in self test on the ESL series smoke detectors may be unreliable.

If the built-in self test is required, it should be done in the normal operating mode with the zone speed set to 3 seconds or higher. Please read Section 7 thoroughly, especially if you have never programmed the before. The quick reference chart can be used for keeping track of how options have been pro- grammed for an installation. You must be in Step Programming Mode also known as mode 27 to program the panel.

See the following sections for details. Using Step Programming The digits appear on the right side of the display and scroll to the left as you continue to enter data. The way you move through Mode 27 may also vary from how it is described here. Enable the printer if your installation includes a printer in- terface. The is not UL listed for use with the Enables 24V power.

Do NOT disable. These digits are reserved by the manufacturer for future use. Knigth Step 3. More System Options Display Description Step 3 allows you to select seven system options shown below. To select an option, press its number. If you select this option, bells will pulse in the pattern shown below for customizing patterns, refer to Steps 27 and 28 5207 silent knight manual 3. Page Step 5. Miscellaneous Options Display Description Step 5 is for programming several system options, including bell supervision.

Select this option if you want walk tests reported to the central station. Page 60 Note: This very fast response time can increase the possibility of false alarms, since transients and other interference can set off alarm conditions in such a short time span.